4.6 build

Post by **jbxx** » August 27th, 2011, 1:21 pm

Getting close

Post by **Zorm** » November 30th, 2011, 10:10 am

how much were the pistons?

Post by **jbxx** » December 4th, 2011, 10:27 am

$475 they may not be this price now.
Just checked the catalog. $429 now.
http://www.bulltear.com/catalog/product ... 4bk2st6gj4
J.B.

Post by **jbxx** » February 25th, 2012, 3:43 pm

Almost there!

Post by **Gorillaxj** » February 26th, 2012, 8:05 am

Looks good! I like the orange a lot, that's what I was planing on painting mine! keep up the good work!

Post by **Antifreeze2** » February 26th, 2012, 8:34 am

I like how it matches the RRs and clutch

Post by **jbxx** » June 24th, 2012, 5:21 pm

Yup that's a brand new AX-15 behind the longest stroker build in history.

Post by **shawnxj** » June 24th, 2012, 10:54 pm

na yours isn't the longest in history. i started mine 2 years ago and still haven't finished it...almost have all the parts though and i have an assembled short block. 1 day i'll have the cash to finish the head

am i seeing things or is that the renix intake and throttle body?

Post by **jbxx** » June 26th, 2012, 4:07 pm

Yuppers it's Renix. Decided to stay with that to minimise the difficulty of the swap.

Post by **shawnxj** » June 26th, 2012, 7:45 pm

You should atleast get the throttle body bored out or your going to suffocate that new engine

Post by **jbxx** » June 28th, 2012, 4:51 pm

It'l never go over 4K.
I did the calculations from "Performance Fuel Injection Systems".
If I get a little time I'll post the calcs. But if I remember correctly, according to the calcs the TB should be fine.
I realize that the real word is sometimes quite different than calculations, but as I said before, I kind of want to change a little at a time.
This makes t-shooting easier. I'll be happy just to get it in and running!
I have half a dozen TB's from different Jeeps floating around the shop, so I can experiment after initial startup.
J.B.

Post by **jbxx** » June 28th, 2012, 4:53 pm

P.S.
I pulled the engine April 2010!

Post by **shawnxj** » June 29th, 2012, 3:26 pm

I'm sticking with my renix tb as well but I'm going to have it bored out to 60mm so I don't have to buy all the expensive adapters to make the newer tbs work with the older computer but I'm going with the newer intake for the better flow and I figure the intakes only dealing with air and vacuum so it can't really mess anything up

Post by **Muad'Dib** » June 29th, 2012, 4:34 pm

Newer intake + RENIX TB still ='s Adapters...

Post by **shawnxj** » June 30th, 2012, 8:57 am

ya but that i can make out of a $10 piece of aluminium....which is what i did

4.6 build

Re: 4.6 build

Re: 4.6 build

Re: 4.6 build

Re: 4.6 build

Re: 4.6 build

Re: 4.6 build

Re: 4.6 build

Re: 4.6 build

Re: 4.6 build

Re: 4.6 build

Re: 4.6 build

Re: 4.6 build

Re: 4.6 build

Re: 4.6 build

Re: 4.6 build

Who is online